Porsche 993 Chassis Upgrades & Strut Braces 1994 to 1998

911 R / ST / RS / RSR Front Windscreen Securing straps. Laser cut alloy. Folded to match the Windscreen profiles. Blank ready to be drill to suit your type of fastenings. Ideal for Race & Rally Lexon & Perspex Windscreens

911 R / ST / RS / RSR Front Heater Box Delete / block off plates. Kit includes; 2x center covers , 2x outer covers & 4x gaskets.

Stainless Steel. Fits all Porsche 911 coupe 1974 to 1998. The harness guide bar attaches to factory mounting points in "B" pillars & shoulder straps. Designed to allow enough seat travel for tall drivers.

For mounting lower center harness strap on 5 & 6 point harnesses. For 911, 964 & 993 Models from 1974-98. Attaches to floor pan using factory seat mounting points

In response to the many requests from Porsche drivers looking for a harness guide bar that would not only guide their driving harnesses but also allow them to mount their harnesses directly to the bar, BK developed the "Harness Truss".for Motor Vehicle Seat Belt Anchorages-Performance Requirements. It's strong, yet it weighs only a fraction of what a support of the same strength made from tubular or bar steel would weigh. The Harness Truss is precision water-jet machined for a perfect fit into Porsche factory mounting points. This type of machining is accurate and does not create heat affected areas in the metal which can alter tensile strength. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. Material: 6061-T6 aluminum skeleton and reinforcing bar. Type 304 stainless steel brackets. Finish: Anodized aluminum with satin stainless mounting brackets. Models: 911 Coupes '74 - '98 Installation: Bar attaches to factory mounting points in "B" pillars. Harness Truss is designed to allow enough seat travel for tall drivers. The stainless steel mounting brackets can be left installed in the "B" pillars to easily remove and remount the bar in minutes.

Genuine Cibié Pallas Oscar Series H1 Driving Lights With Mounting Plates. Ideal for Classic Rally & Night Racing. Can also be used on later water cooled models and for Retro Look. H1 Bulbs Diameter; 180mm EU approved / E-marked Direct replacement Units.

Ideal for track day and racing cars where secure easy access is required. Available as carbon look or plain black. These EuroCup catches fit all models 1965 - 2013. Price per pair

OEM Race part for all cars 1982 -Onwards Length; 75mm through bumper boss + strap (90mm long)

OEM Race part for all cars 1982 -Onwards Length; 40mm through bumper boss + strap (75mm Long )

EuroCupGT carbon fibre strut brace is more rigid & significantly lighter than the steel ones. It is fully adjustable with anodised alloy locking rings to make fitting easy. All parts required to fit are included. The overall weight is around 900g (including mountings)

964 / 993 RHD Drivers side floor board. R styled floor boards in Aluminum for Manual cars

Bonnet Boot Engine Lid & Bumper Pin Hold Down Kit. 2x lightweight threaded Billet aluminum dome pins. 2x flush mount Delrin receiver discs. 2x locking pin clips and Nuts.

By using computer engineering and digital design STOMSKI RACING has developed the FIRST truly symmetrical 911 Semi-Solid Engine/Transmission Mount, thus allowing you to run stiffer mounts without sacrificing comfort or ride quality.  Our symmetrical design allows you to custom tune your ride- determining feel, function, and fun.  Because our SS mounts are SYMMETRICAL, you can now properly use them either as an engine mount OR inverted as a transmission mount on Boxster & Cayman models. Unlike other non-symmetrical SS mounts, there is no compromise when using SR135 inverted as a transmission mount because SR135 is symmetrical and thus FULLY supports and FULLY absorbs in BOTH positions/directions. Road tested and track proven, STOMSKI RACING's SR135 provides better shifting, better weight transfer, better handling, crisper throttle response, better acceleration, and of course GREAT looks, without any loss of comfort.  Mounting  comes complete with an  aluminium housing, stainless steel sleeve and disks spacers & a M12 Schnorr washer. Sold as 1 Pair (2x Mountings)

EuroCupGT-Pro ADJUSTABLE RACE SEAT BRACKETS. These seat frames have been developed specially for maximum strength, rigidity and longevity. ( one Pair / Seat ) Can Be Solid Mounted to Floor or mounted to Porsche or EuroCupGT seat Runners. Fits All; GT3, GT4, Recaro, Sparco, OMP & EuroCupGT Seats.