Seat & Seat Mounting Hardware

OEM Race Seat Belt Part for 2" Lap & Crotch straps. ( Can also be used on 2" Shoulder Straps )

Early repoduction LWT seat brackets. Ideal for the Classic Recaro low back or Shell Back Seats and Club Sport Racing Seats. Sold per seat (1 Pair)

For mounting lower center harness strap on 5 & 6 point harnesses. For 911, 964 & 993 Models from 1974-98. Attaches to floor pan using factory seat mounting points

For GT3 & Race Seats fitted in 996 / 997 Boxster & Cayman models. For mounting lower center harness strap on 5 & 6 point harnesses using a one-piece seat with anti-sub strap pass-through. This mount works in conjunction with factory & EuroCupGT 996/997/Boxster Manual slider kit and with the BK R-2030 fire extinguisher mount.

In response to the many requests from Porsche drivers looking for a harness guide bar that would not only guide their driving harnesses but also allow them to mount their harnesses directly to the bar, BK developed the "Harness Truss".for Motor Vehicle Seat Belt Anchorages-Performance Requirements. It's strong, yet it weighs only a fraction of what a support of the same strength made from tubular or bar steel would weigh. The Harness Truss is precision water-jet machined for a perfect fit into Porsche factory mounting points. This type of machining is accurate and does not create heat affected areas in the metal which can alter tensile strength. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. Material: 6061-T6 aluminum skeleton and reinforcing bar. Type 304 stainless steel brackets. Finish: Anodized aluminum with satin stainless mounting brackets. Models: 911 Coupes '74 - '98 Installation: Bar attaches to factory mounting points in "B" pillars. Harness Truss is designed to allow enough seat travel for tall drivers. The stainless steel mounting brackets can be left installed in the "B" pillars to easily remove and remount the bar in minutes.

Satin finish stainless steel. Porsche All 911, 924 944 968 928 964 993 996 997 Boxster & Cayman Models Secures snap-in Harness lap belts to outside seat belt mounting point. Allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats.

Satin finish stainless steel. Porsche All 911, 924 944 968 928 964 993 996 997 Boxster & Cayman Models Secures snap-in Harness lap belts to outside seat belt mounting point. Allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats.

Satin finish stainless steel. Porsche 911 924 944 968 964 993 Boxster Cayman & 996 / 997. Secures snap-in lap belts to factory tunnel side (inside) seat belt mounting point. Allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats

Ideal when replacing Porsche seats with EuroCupGT racing seats or other GT or Racing seats. Price each (One Kit )

EuroCupGT Bucket Seat Runner Kit. For All Models. Note. You may need other Hardwear to Mount these runners when fitting Aftermarket Race Seats. Please see other options in this section

Clear Anodized Aluminum, fits all models. Attaches to roll cage. Fits 1.5" roll cage also available for 1 5/8" roll cage, please specify diameter when ordering

Automatically disables passenger's front and side airbags when the plug-in connector on your Porsche child seat is inserted. Includes ISOFIX retaining bracket and switch for deactivating passenger airbag. Note: When carrying children weighing up to 27 kg, the passenger airbag must always be deactivated. Please use model & year drop down's in checkout & notes for Left or Right Hand Drive. ( UK = Right Hand Drive / Europe = Left Hand Drive)

Fits in Floor to secure Seat Mounting & Runners

RTB2005C Racetech aluminium clamps for back-mounting seats. Precision cut from a 20mm thick 5083 alloy sheet. Sold as a pair, these clamps fix around a rollcage tube and bolt to the RTB2005B bracket. This allows you to quickly and effectively back-mount a Racetech 9119 series seat to the chassis / rollcage at the shoulder level. Supplied with 2x M8 bolts and 2x flat washers. Note; there are Three Size of Roll Cage Tube fitting options that can be ordered; 38mm ( 1 1/2") 41mm ( 1 5/8") 44.5mm (1 3/4")

RTB2115B: Racetech 5mm aluminium (5083) bracket for back-mounting seats. This bracket bolts to the shoulder beam of Racetech 9119 series seats and working in conjunction with RTB2005C clamps, allows you to fix the seat to the lateral / diagonal rollcage tube. Requires four holes drilled to bolt on the clamps once you have the seat setup in the optimum driving position.

Stainless Steel Seat Belt clip to be used with Air Bag Deactivation devices & Recaro Baby & Child seats. For Front Passenger Seat fitting. Can also be used for Drivers seat to Stops warning alarm buzzer

This Hardware kit is required for installation of the Seat Belt mounts in 1974 - Onwards. All models

Now you can provide forced air induction to your Racetech 119 or 129 series race seat. Increase driver comfort by removing latent heat to the lower back. Especially useful in longer or enduro race events, this air cooling maintains a level of comfort for the driver, enabling optimum performance and less heat stress and fatigue. Kit includes: 12VDC inline cooling blower - 122 CFM Silicone reducer - 76mm > 51mm 51mm flexible duct hose - 1250mm long Use with a NACA or roof duct and 3 (76mm) intake hose for maximum performance. Use with a NACA or roof duct and 3 (76mm) intake hose for maximum performance.

Secures Recaro Club Sport Pole Position Seat to 996 997 Boxster & Cayman factory sliders.

For GT3 seats mounted to the floor , Passenger side for Right Hand Drive Cars & Drivers side for Left hand Drive Cars. Will Also requires Part R-9042 Side Mount to Floor Adapter

For GT3 seats mounted to the floor , Drivers side for Right Hand Drive Cars & Passenger side for Left hand Drive Cars, Also requires Part R-9042 Side Mount to Floor Adapter

For Recaro & Porsche GT3 Seats to original Manual Sliders runners, Passenger side for Right Hand Drive Cars & Drivers side for Left hand Drive Cars

For Recaro & Porsche GT3 Seats to original Manual Sliders runners, Drivers side for Right Hand Drive Cars & Passenger side for Left hand Drive Cars

RTB1003S: Racetech zinc-plated, 3mm thick steel brackets for side-mounting race seats. Sold as a pair. These brackets are suitable for use with the following seat models: RT1000 & RT4000W

RTB1005M: Racetech milled aluminium bracket for side mounting seats. This pair of mounts is the same shape and hole spacing as the RTB1003S but half the weight. 5mm thick 5083 alloy. Fits the following seat models: RT1000 & RT4000W

RTB1009M: Racetech mill-finish 5083 aluminium brackets for side-mounting seats. 5mm thick. Sold as a pair.

Secures Recaro Pole Position Seat & SPG xl Seat to 996/997/Boxster factory sliders. Passenger Side for Right Hand Drive cars & Drivers Side for Left hand Drive cars.Price is per pair

R-9072 UK Drivers Side Side Mount Brackets for Sparco Evo, Sparco Pro 2000 for manual sliders 996 , 997, Boxster, Cayman

R-9071 UK Passenger Side Side Mount Brackets for Sparco Evo, Sparco Pro 2000 for manual sliders 996 , 997, Boxster, Cayman

EuroCupGT-Pro ADJUSTABLE RACE SEAT BRACKETS. These seat frames have been developed specially for maximum strength, rigidity and longevity. ( one Pair / Seat ) Can Be Solid Mounted to Floor or mounted to Porsche or EuroCupGT seat Runners. Fits All; GT3, GT4, Recaro, Sparco, OMP & EuroCupGT Seats.

Fits All EuroCupGT seats and other Racing seat makes. Powder Coated in Black. Light & Strong. Ideal for Motorsport & Road use. Seat Belt Anchor Points on both sides. Price is per pair

Full Seat Fitting Kit for EuroCupGT shell back Seat range for All Late Model Cars 996 997 Boxster & Cayman. Includes runners, side mounts with threaded seat belt anchors & Floor mounting plates. Can also be used on other aftermarket & Porsche racing seats.