Porsche 944 Chassis Upgrades & Strut Braces 1982 to 1992

Ideal for Front Bonnet and Rear Engine Lid or Glass Hatch

Small Rubber Tie Down Straps. Ideal for Race Rally & Backdates

For mounting lower center harness strap on 5 & 6 point harnesses. For 911, 964 & 993 Models from 1974-98. Attaches to floor pan using factory seat mounting points

Stainless steel. Fits Porsche 944, 968, 928, 911 964 & 993 Models with power Electric seats. Attaches to factory seat track hardware on Front Seat

Satin finish stainless steel. Fits Porsche 911 964 993 924 944 & 968 with non-power seats. Attaches to factory seat track hardware under front Seat.

Stainless steel GoPro Camera mount is three axis adjustable to properly position camera. Strap secures camera to mount. Attaches to Roll Cage harness guide bar tubing

In response to the many requests from Porsche drivers looking for a harness guide bar that would not only guide their driving harnesses but also allow them to mount their harnesses directly to the bar, BK developed the "Harness Truss".for Motor Vehicle Seat Belt Anchorages-Performance Requirements. It's strong, yet it weighs only a fraction of what a support of the same strength made from tubular or bar steel would weigh. The Harness Truss is precision water-jet machined for a perfect fit into Porsche factory mounting points. This type of machining is accurate and does not create heat affected areas in the metal which can alter tensile strength. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. Material: 6061-T6 aluminum skeleton and reinforcing bar. Type 304 stainless steel brackets. Finish: Anodized aluminum with satin stainless mounting brackets. Models: 911 Coupes '74 - '98 Installation: Bar attaches to factory mounting points in "B" pillars. Harness Truss is designed to allow enough seat travel for tall drivers. The stainless steel mounting brackets can be left installed in the "B" pillars to easily remove and remount the bar in minutes.

Stainless steel. Bar attaches to strut towers. Adjustable rod ends allow precise preloading

Ideal for track day and racing cars where secure easy access is required. Available as carbon look or plain black. These EuroCup catches fit all models 1965 - 2013. Price per pair

This cross brace bolts between the rearmost mounting points of the front control arms. It resists deflection of the chassis at those points, which can occur under heavy braking and cornering. Precision waterjet machining allows for an intricate structure, providing superior stiffness at an exceptionally light weight. Material: 6061 T-6 aluminum skeleton, 304 stainless steel mount brackets Finish: Anodized aluminum Weight: 2.6 lbs

Stainless Steel. The harness guide bar attaches to factory mounting points in "B" pillars & shoulder straps. Designed to allow enough seat travel for tall drivers

OEM Race part for all cars 1982 -Onwards Length; 40mm through bumper boss + strap (75mm Long )

OEM Race part for all cars 1982 -Onwards Length; 75mm through bumper boss + strap (90mm long)

Bonnet Boot Engine Lid & Bumper Pin Hold Down Kit. 2x lightweight threaded Billet aluminum dome pins. 2x flush mount Delrin receiver discs. 2x locking pin clips and Nuts.

EuroCupGT-Pro ADJUSTABLE RACE SEAT BRACKETS. These seat frames have been developed specially for maximum strength, rigidity and longevity. ( one Pair / Seat ) Can Be Solid Mounted to Floor or mounted to Porsche or EuroCupGT seat Runners. Fits All; GT3, GT4, Recaro, Sparco, OMP & EuroCupGT Seats.

Bar attaches to strut towers. Adjustable rod ends allow precise pre-loading

Stainless steel. Bar attaches to strut towers. Adjustable rod ends allow precise preloading